lmr1a - lmr1m glass passivated junction fast recovery rectifiers prv : 50 - 1000 volts io : 1.0 am p ere features : * glass passivated junction chip * high surge current capability * high reliability * low reverse current * low forward voltage drop * fast switching for high efficiency * pb / rohs free mechanical data : * case : m1a molded plastic * epoxy : ul94v-o rate flame retardant * lead : axial lead solderable per mil-std-202, method 208 guaranteed * polarity : color band denotes cathode end * mounting position : any * weight : 0.20 gram (approximately) maximum ratings and electrical characteristics rating at 25 c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20%. symbol lmr1a lmr1b LMR1D lmr1g lmr1j lmr1k lmr1m unit maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward current 0.375"(9.5mm) lead length ta = 55 c peak forward surge current, 8.3ms single half sine wave superimposed on rated load (jedec method) maximum peak forward voltage at i f = 1.0 amp. v f 1.4 v maximum dc reverse current ta = 25 c i r 5 a at rated dc blocking voltage ta = 100 c i r(h) 50 a maximum reverse recovery time ( note 1 ) trr 150 250 500 ns typical junction capacitance ( note 2 ) c j 50 pf junction temperature range t j - 65 to + 150 c storage temperature range t stg - 65 to + 150 c notes : ( 1 ) reverse recovery test conditions : i f = 0.5 a, i r = 1.0 a, irr = 0.25 a. ( 2 ) measured at 1.0 mhz and applied reverse voltage of 4.0 v dc page 1 of 2 rev. 02 : april 28, 2009 a a 25 rating i fsm i f(av) 1.0 m1a dimensions in inches and ( millimeters ) 1.00 (25.4) min. 0.085(2.16) 0.075(1.91) 0.138(3.51) 0.122(3.10) 1.00 (25.4) min. 0.024(0.60) 0.022(0.55) iatf 0060636 sgs th07/1033 th09/2479 th97/2478
rating and characteristic curves ( lmr1a - lmr1m ) fig.1 - reverse recovery time characteristic and test circuit diagram + notes : 1. rise time = 7 ns max., input impedance = 1 megaohm, 22 pf. 2. rise time = 10 ns max., source impedance = 50 ohms. 3. all resistors = non-inductive types. fig.2 - derating curve for output fig.3 - maximum non-repetitive peak rectified current forward surge current 0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100 ambient temperature, ( c) number of cycles at 60hz fig.4 - typical forward characteristics fig.5 - typical reverse characteristics 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 page 2 of 2 rev. 02 : april 28, 2009 60hz resistive or inductive load 0.8 0.6 0.4 0.2 1.0 100 10 1.0 24 0 30 0 18 12 6 0.1 10 80 0.01 0.01 1.0 0.1 100 140 0 20 40 60 120 percent of rated reverse voltage, (%) peak forward surge current, amperes average forward output current, amperes forward current, amperes reverse current, microamperes t j = 25 c t j = 100 c t j = 25 c pulse width = 300 s 2% duty cycle 8.3 ms single half sine wave ta = 50 c set time base for 50-100 ns/cm trr + 0.5 a 0 - 0.25 a - 1.0 a 1 cm 50 vdc (approx.) oscilloscope ( note 1 ) 1 50 10 d.u.t. pulse generator ( note 2 ) forward voltage, volts iatf 0060636 sgs th07/1033 th09/2479 th97/2478
|
